KBS Klean

What is the diluted solution ratio for a ultrasound machine?

What is the the appropriate dilution to remove car wax prior to clear coat?

67 Tbird engine compartment restoration. Engine and transmission are removed (for rebuilds and restoration. Are remaining wiring and hoses safe when spraying KBS Klean? I can take some precautions, but I don’t see how it’s practical to encapsulate these items.

Can you give me the lowdown on plastic headlight lens restoration with your product? This product is recommended by a popular internet automotive bulb seller/expert. Do you dilute your product? Any special technique to restore a hazed lens?

What would be the best approach to drying the surface after KBS Klean is washed out? The surface is known to lose its energy fast, at the same time it must be dry. So the longer the drying time, the less surface energy remains. Are there any methods beside heating it up?

I completely cleaned portion of my 57 Chevy frame. I used solvents, scrapers, hand wire brush and an angle grinder with a wire wheel. I removed all the visible contamination. I then spayed an aerosol "Universal Bonding Primer" to the frame area. Can I start by using "Clean" and proceed to "Rustblast" and Rustseal"? Is Rustseal the best product for the frame? What product do you recommend for finish coat on inside and outside metal fender liners?

Got a heavy buildup of algae & slime on my boat. Will KBS Klean work to remove it?

I have a very large 100 year old bell with mounts. It's a very rough cast iron surface. I used a wire wheel off my angle grinder to strip off old paint and rust. I'd like to use Diamond Finish Clear to protect the metal with it's current patina while it sits outside for the rest of it's life. Can I use KBS Klean, the the Diamond Finish without having to also use the Rust Blast? If Rush Blast is required, please advise why? Thanks for your time and consideration.

I bought the RustSeal sample kit for use on a small area on a BMW motorcycle engine. The area is on a forward facing non-ferrous cast plate, probably aluminum alloy. I have been able to remove most of the paint from the area. In your directions you indicate that application times and dilution rates for KBS Klean should be kept to a minimum. Can you be more specific similar to the directions for KBS Klean use on non-ferrous metals?

I'm getting ready to start my project with the KBS Klean, Rust Blast and Rust Seal. I only have one bottle and sprayer. Can I use the same bottle and sprayer for KBS Klean and Rust Blast?

I noticed it says to dilute KBS Klean with water 1 to 1 for dirty surfaces. Can I use KBS Klean straight because the metal I'm cleaning is really dirty? I'm wondering if this would work even better than diluting with water.

I've got the KBS kit on order, arriving in a couple of days, to use on a motorcycle gas tank that sat for a couple of years and has rusted on the inside. The tank has an internal fuel pump and fuel strainer assembly consisting of a mix of plastic and metal parts. Is it safe to use the cleaner and rust remover on these parts, or not? And would it be safe to run the cleaner through the fuel pump? Many thanks.

Is KBS Klean suitable for use prior to spraying automotive paint? I'm looking for a solvent to remove oils, wax, grease, and silicone from *painted* surfaces prior to coating, but preferably a water-based solution. Right now I am in the middle of sanding the existing paint before I spray some sealer and want to get rid if any sanding residue and the like, aka above from the surface. It sounds like KBS Klean is suitable for all surfaces. Just looking for some feed back before I prime and seal.

I'm doing your 3 step process and I just finished doing the Rust Blast. I just realized I forgot to dilute the KBS Klean with water when I used it. Is this going to mess everything up? Should I start over? Any suggestions would be great!

I have some left over KBS Klean after painting my frame. Can I use this on interior counter tops in my kitchen?

I have some new metal straight from the factory so it's clean. Do I still need to use the KBS Klean or can I skip to the rust blast?

Can you recommend a cleaning product for a Diesel Tank? I was told that Diesel fuel has paraffin in that coats the tank making it difficult to clean. Advise please.

Could this product conceivably be mixed with a hygroscopic solvent such as ethanol or lacquer thinner for extreme crud removal applications such as coked up diesel engine parts?

I want to try KBS 3 Step System. The bottom of my SUV has been protected by petroleum based solvent-free products. Can KBS Klean dissolve and remove that oily stuff from the frame and the car floor?

Will KBS Klean harm the paint on the outside of my gas tank when I am using it to prep for the Tank Sealer?

Can KBS Klean be used in my pressure washer? I like how well KBS Klean works and it would be great if I could use it through the suction tube on my pressure washer for washing the side of my house and other things.