KBS Top Coater
KBS Top Coater is a superior spray paint formulated for maximum coverage and professional looking results. KBS Top Coater is an ideal top coat paint for RustSeal when the area will be consistently exposed to sunlight. KBS Top Coater is a very high solids paint does not run or sag, and gives at least twice the coverage of conventional spray paints.
Subforums
-
KBS Top Coater is a superior coating formulated to be brushed, rolled, or sprayed offering maximum coverage and professional looking results. KBS Top Coater is a direct to metal exterior grade coating that adheres permanently to steel and aluminum surfaces. KBS Top Coater is a very high solids paint that does not run or sag and gives at least twice the coverage of conventional paints.
5,262 visits to this link
13 topics in this forum
-
I see the q&a about mixing colors... Do you have any examples of mixing? I'd like to have a red that isn't quite as bright as your Safety and Fire red. What might be a "normal" mix ratio? For instance, one part black with 20 parts red(?). Any experience with that?
-
- 0 replies
- 566 views
-
-
Two questions, What is the shelf life if unopened product. Second how do I determine if it is unusable. I purchased some of you products for a project, then life happened and I am just getting back to it. I am planing a project and prefer the pint cans, I set up my coating of areas so I have about a pints worth of coating to apply. So is it ok to buy a multi year supply at once or buy a pint at a time.
-
- 0 replies
- 329 views
-
-
I have a gallon of Green Camo, it does not match even close to what is pictured. The color is closer to the forest green other then a matte finish. What tint suggestion to get closer to the picture of a lighter grayish green or one closer to Olive or WWII type? I also have desert tan. That might do the trick giving it a bit more brownish green. Just not sure where to start without wasting a whole gallon. TIA
-
- 1 reply
- 3.1k views
- 1 follower
-
-
If I was to sand the Water based exterior Latex paint with 300 grit, would it be then ok to use Top Coater? Wanting to do poor man fiberglass first then cover with the Top Coater.
-
- 1 reply
- 1.2k views
- 1 follower
-
-
Fixed some rims used diamond clear for finishing
- 1 reply
- 1.8k views
-
With the time between coats of about 1 hour, what is the pot life of the Top Coat in the spray gun?
-
- 1 reply
- 1.7k views
- 1 follower
-
-
I purchased rust sealer and top coater, but forgot to purchase the thinner. So is there a off the shelf thinner I can use to spray and what ratios. I am under a time constraint to finish the project
-
- 1 reply
- 2.4k views
- 1 follower
-
-
Will baking parts painted with Top Coater help cure the part and make the paint stronger?
-
- 1 reply
- 1.6k views
- 1 follower
-
-
I painted a couple of parts on Sunday and now it is Tuesday. The parts are still tacky. Is that normal? The humidity was <60% when sprayed then the parts were moved inside where the humidity is <40%.
-
- 1 reply
- 1.7k views
- 1 follower
-
-
I thinned the top coater white with about 10% kbs thinner and painted out my hplv gun. The spray pattern was a little thick like small fabric thread looking paint. See the picture for an up close view. I was wondering is this the intended outcome or is it suppose to be smooth?
-
- 3 replies
- 3.3k views
- 1 follower
-
-
How long do I have to wait to paint KBS Top Coater over Rust Seal?
-
- 1 reply
- 4.6k views
- 1 follower
-
-
I painted 2 coats of Rust Seal and now I'm looking to top coat it with KBS Top Coater. I'm going to put 2 coats. How long do I have to wait to paint my second coat?
-
- 1 reply
- 4.8k views
- 1 follower
-
-
Can you paint KBS Top Coater directly onto bare metal?
-
- 1 reply
- 2.9k views
- 1 follower
-
