Jump to content
Ordering & InfoSupport ForumSupport DeskContact UsEmail Sign-UpReseller Finder

Guest

Members
  • Posts

    189
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by Guest

  1. I know it is best if I get consecutive coats of DiamondFinish Clear on within 8 hours but what happens if that is just not possible? How do I insure that the next coat will adhere to the previous coat?
  2. Where can I get the tape for sealing when preparing to seal a motorcycle tank?
  3. Can DiamondFinish Clear be used over acrylic paint on a canvas?
  4. I have some rust on my truck and I was wondering what type of rust prevention does the Bed Renu have. I know you have Rust Seal which I've used and works great but I want to try only the Bed Renu as I like the textured look. Would Bed Renu offer any rust prevention for me?
  5. Will Diamond Clear stand up to continuous exposure to damp salt salt air? I want to coat stainless steel? Im looking for a clear coat for beach house.
  6. I'm going to use your Rust Converter and there are some areas that will see the sunlight. Will the discolor or fade Rust Converter?
  7. I have 15 gallon fuel tank I'm sealing with your Tank Sealer. Can I take the excess Tank Sealer that I drain out of the tank and put it back into the can and seal it up?
  8. What is the best type of blasting for surface preparation for your products?
  9. Can I paint your Diamond Finish Clear over an oil based paint that has fully cured? If so, how should I prep the surface?
  10. I have an interior wooden table I want to clear coat. What would you recommend I should use, aerosol or brush on?
  11. Can I paint Rust Seal over any type of paint?
  12. How long do you leave Rust Blast in an aluminum gas tank to etch the surface?
  13. I'm using your galvanized steel Rust Seal. It's really thick and I know in the directions it says you can thin up to 10%. What will happen if I thin it more than 10% because I think it will need it?
  14. I have a bunch of small springs for car hoods. I want to paint them with Rust Seal and Black Top but it would be nearly impossible to brush or spray it on. I've dipped a couple of them but It gets a little thick at the bottom once it sits there for a little bit. Do you have any suggestions that could help with the paint running and building up at the bottom?
  15. I'm getting ready to start my project with the KBS Klean, Rust Blast and Rust Seal. I only have one bottle and sprayer. Can I use the same bottle and sprayer for KBS Klean and Rust Blast?
  16. I need to paint my engine and I'm going to use your Motor Coater. I noticed you have a high temperature XTC Primer. Would this be beneficial to use on my engine before I paint the Motor Coater on? It seems like it would give it better protection.
  17. I have a little bit of surface rust on the inside of my tank. I don't want to use a sealer to coat the inside I would just like to use the KBS Klean and Rust Blast to dissolve the rust. Is this something that should work for me?
  18. I painted my first coat of KBS Maxx on Saturday this past weekend. I've decided to put another coat and I was wondering if I can go ahead an paint the next coat or do I need to do some type of surface prep for the KBS Maxx to adhere to itself?
  19. What is the shelf life of Black Top? Opened and unopened.
  20. I'm using some seam sealer and was wondering how to apply the Rust Seal with it. Should I put Rust Seal down first and then seam sealer or seam sealer and then Rust Seal?
  21. Guest

    KBS Klean

    I noticed it says to dilute KBS Klean with water 1 to 1 for dirty surfaces. Can I use KBS Klean straight because the metal I'm cleaning is really dirty? I'm wondering if this would work even better than diluting with water.
  22. Can I paint your Motor Coater on the oil pan of my car? If not, what would you recommend?
  23. It seems like your Tank Sealer works very well on old tank. Can I use the Tank Sealer on a new tank?
  24. Guest

    Bed Renu

    What preparation is needed to apply Bed Renu in the bed of my truck?
  25. Can I use KBS Maxx on an engine block? If so, how would I prep the surface?
×
×
  • Create New...